3D Printing

better Printrbot+ 3d prints

Monday, August 6th, 2012
 two prints of Mr. Jaws
The above print of Mr. Jaws was with a .4mm layer height. The print at bottom is at a .2mm layer height. Smooth!

I disassembled and reassembled the Printrbot+ this weekend. I’ve now upgraded it quite a bit, with accuracy and speed in mind. It now uses GT2 belts and molded polycarbonate/brass pulleys in place of its stock XL belts and printed pulleys, and Acme leadscrews instead of the original threaded rod. Aluminum 5mm-6.35mm couplers connect the leads crews to the z-axis motors, instead of the original set of molded plastic couplers. I bought all of the parts for this round of upgrades from techpaladin.com. Nathaniel was super-helpful, and informed me of parts I’d need that became in-stock just before my order shipped and in time for me to add them.

The result of these upgrades make me very happy. First I printed a popular test object, Mr. Jaws. It went so well that I decided to push the envelope and drop the layer height setting from .4mm to .2mm. This higher-resolution print took twice as long (~27 minutes vs ~14.5 minutes), but the edges of the print are much smoother and the ridges much less pronounced.

 Yoda Lite at 50% scale and .2mm layer height
Yoda Lite at 50% scale and .2mm layer height
This morning was time to try printing Yoda Lite. I brought its STL file into the program “Slic3r” to convert it to the geode commands that drive the Printrbot+, with layer height set to .2mm, and the software predicted a 2 hour print time. I lowered the fill percentage to .3 from .45 so that the object would be more hollow, but it still was going to take more time than I had if I wanted to arrive to work on time. So I set the object to print at 50% scale and the time estimate dropped to about a half-hour. Capital. 1

I had one abortive print attempt in which 1/3 of yoda printed and then the object stuck to the extruder nozzle and popped from the bed. In order to prevent this from happening again, I adjusted the z axis endstop to print the first layer slightly lower and more flattened by the extruder into the kapton surface of the print bed. You can see this flattening in the circle of plastic or “skirt” around Yoda. It’s a little more flattened than I’d like, as every subsequent layer also gets flattened and the detail in the print is affected, but I wanted it to really stick to the bed this time. The result has some problems around the ears, but made me happy nonetheless. It’s a definite improvement over the pre-upgrade prints.

  1. Never used that one before, but “Yay” just didn’t look very professional. ↩︎

My first blob (and some better blobs)

Friday, August 3rd, 2012

A blob meant to be a clip to hold a piece of glass on the printbed.
The first somewhat-recognizable blob I printed, a rather squishy version of technoswiss’s printrbot glass clip.

On Sunday, I made a few last-minute adjustments to the Printrbot+, wired the motors and sensors to its circuit board, loaded the software on my computer, powered it up, plugged in the USB cable, and gave it a whirl. Shockingly, the blue smoke remained inside the board and all axes and the extruder responded to computer control.

I applied some blue painter’s masking tape directly to the print bed as a surface, loaded up the extruder, and set it printing technoswiss’s ‘Printrbot glass clips’ so that I could install the 8×8″ sheet of borosilicate glass I’d purchased from McMaster Carr to use as a print bed. The extruded plastic would not stick to the tape. I increased the heat of the bed and extruder and had some success, but eventually gave up on that print surface and applied a surface of heat-resistant Kapton material to the print bed. That worked much better, and produced the squishy version of the clip visible above.

a much improved print
At left, the first print. At right, a better print of the same object after some calibration. The countersunk hole for the bolt can be seen.

Monday’s subsequent attempts at printing didn’t stick to the Kapton, and I realized that I needed to recalibrate the Z-axis and attempt to level the bed, as the hot end of the extruder was just not getting close enough (it’s supposed to print from a distance roughly equal to the thickness of a piece of paper). Problem solved, but as it printed I noticed that the printhead was squishing the printed object around as if it were a block of cheese. I reasoned that this was due to excessive bed temperature, excessive hot-end temperature, a miscalibrated z-axis (the head was not raising enough between layers), and a miscalibrated extruder (it was extruding too much plastic). A few measurements and adjustments later, and a much better print was produced. It seemed like it would be usable, so I printed 3 more.

Img 1543

And then it seemed time to print some replacement parts before the bits that had broken in assembley stopped working. I’d split the y-axis pulley by over tightening and had also broken a y-axis belt clip. I downloaded the files and tried printing these more complicated parts. Unfortunately at this point the broken y-pulley was beginning to slip on the motor shaft, so the y-axis was not stable. The pulley is probably not going to be usable, but it does look cool. The belt clip is slanted due to the slipping y-axis, but it’ll probably work fine. I have more precise GT2 belts and pulleys on order, so it should be printing much more accurately by next week.

The total results of my first couple of days of printing with the Printrbot+.
The total results of my first couple of days of printing with the Printrbot+.

What I did this weekend

Monday, July 23rd, 2012

The most challenging puzzle I’ve yet assembled, with clues scattered over the net –the Printrbot+. Now mechanically complete, but the tasks of wiring it up and the endless tweaking remain.

my assembled Printrbot